Feuerball aus gebogenem Stahldraht mit Kevlarschlauch überzogen.
3 Bälle im Set, inklusive Dosierflasche.
Wird in praktischem Kunststoffbeutel geliefert.
Größe: Ø 68mm
Gewicht: 120g
Ersatzdocht siehe unter "Feuerzubehör / Docht 20mm".
Immer wieder werden wir gefragt, ob diese Bälle auch ohne Handschuhe jongliert werden können. Da nur der Docht im Kern der Bälle brennen sollte, ist es natürlich prinzipiell möglich. Da das Risiko sich zu verbrennen oder dass sich die Finger im Draht verheddern sehr groß ist, raten wir aber generell dazu nur mit feuerfesten Handschuhen zu arbeiten!
Das Jonglieren mit Feuer ist immer gefährlich! Treffen Sie also immer alle möglichen Sicherheitsvorkehrungen - die eigene Gesundheit und die der Zuschauer muß immer Vorrang haben!
FyreBall Lighting Instructions.
For consistent easy lighting and control of the flame size please read these instructions carefully. Adjust valve spout fuel bottle to dispense DROPS OF FUEL onto the two centre wicks. Each FyreBall requires circa 1 cc of fuel.
The preferred fuel is low temperature lamp oil. Alternatively and when lamp oil is unavailable paraffin may be used. Petrol should never be used.
Avoid overfilling or spilling fuel onto the outer Kevlar protective sleeving.
NB Small spillage’s can be dried with high throws.
Individually and with each new FyreBall carry out the following CONDITIONING
Dispense drops of fuel until each wick holder is estimated to be full. Light the centre of ONE FyreBall, matches are the best, and commence one ball juggling until flame is extinguished, about 3-6 minutes. Refuel and set aside. Repeat this procedure with each new FyreBall.
Easilight and Flame Size
Adjust the flame size by withdrawing strands of wick from the wick holder. The more strands exposed the larger the Flame. We recommend starting with a small flame, i.e. with a little wick exposed.
Lighting all 3 FyreBalls
Loosely cluster the FyreBalls.
Hold FyreBalls in one hand, holding match in other hand. Matchbox can be trapped underfoot. Strike and light. Delay juggling for 3-5 seconds. Commence to juggle until flame self extinguishes, or is blown out.
Always refuel after use.
Always seal and secure valve spout bottle after use and before juggling.
Always extinguish lit matches before discarding.
Always maintain constant motion of lit FyreBalls.
Always refuel after use and store wet in a safe place.
Dismantling FyreBalls
FyreBalls are easy to dismantle. If you’re struggling then you’re probably doing it wrong. During dismantling, avoid distorting or over stretching your FyreBalls.
Dismantle and re-assemble one FyreBall at a time. See Sketch.
It should only be necessary to dismantle FyreBalls to replace the Kevlar wicks or the outer Kevlar insulating sleeve.
Slide the long Compression Spring (1) off the Wick holders (2) and gently withdrawn from the centre of the FyreBall.
Rotate the Support Ring (3), which acts like a key ring. The wick holders and silicone grommets (4) can then be withdrawn. Clean each component.
New Kevlar wicking can then be inserted into each wick holder and the dismantling process reversed. Allow about 3-5 mm of Kevlar wick to protrude. Avoid a ragged edge on the Kevlar wick as this produce a variable flame and makes it more difficult to assemble.
Place one wick holder back in position, ensuring that the grommet and wick holder holes are aligned. Position the Support Ring vertically and to one side of the wick holders and rotate the free end of the Support Ring through the holes in the wick holder and the silicone grommet. Continue rotating the Support Ring and pass the free end through the second wick holder. Slide the Centre Spring over one wick holder, then compress the spring and gently repeat the process with the other wick holder.
